Make A Hole In A Leather Belt

In this submit, I'll present you methods to easily add additional holes to a Leather belt, so you possibly can maintain using it even when it's the fallacious measurement. It used to be that if I flipped a belt over and it stated real Leather” I at all times thought, Nice! How a product defines its Leather is vital to understanding the quality of the piece. You've got heard of bonded Leather, high grain Leather, genuine Leather, and if like me always thought it was good as a result of it meant that it was real Leather. Properly, there's a hierarchy, and you may actually inform how good of a Leather grade was used within the manufacturing of whatever you're shopping for.
Remember, the extra 8-11″ in. will the be further tail end of your belt that slips away in the belt loops of your pants whenever you wear it. You don't want this to be too long or too quick; too lengthy, and the belt will look too massive, but too short, and the belt will look too small for you! Upon getting your piece formed how you like it, go forward and prime-sew your fabric Make certain your bobbin as well as your spool of thread on prime are full sufficient that you can sew throughout the border of your belt in one go!



If you want to purchase the instruments, making a belt is usually a little extra cash, but upon getting the tools to make use of, you may easily make extra for a small fraction of the cost! You can also make the hole yourself using a Leather Hole punch instrument or you possibly can take the Leather strap to a shoe restore to allow them to punch the hole for you. Make sure you take the Leather piece that was detached (buckle finish) with you so the hole is cut in the right spot.
One does not simply whip up a top quality Leather belt that can assist tool bag's or holsters by following this method. So no you failed and took good Leather and wasted it. A fantastic belt is 1/four inch thick from two top grain straps bonded and sewn, beveled and burnished coloured with dye and then sealed. I bought 5 belt blanks, 5 belt retains, completely different dyes and balms, burnisher, and Leather edging software all from Amazon and Tandy. To make this project much more authentic I went to the Tanner Goods website and purchased their standard buckles at a cost $8.00 every in silver, brass, copper and black.

In case your prime precedence is a cushty fit, instead put on the belt and pull it to a cushty place, then mark the belt the place the strap tongue touches it. Use heavy objects to crush every finish of the belt, with the location the place the opening shall be punched on top of a block of wood or other hard, flat surface. You may also decide to snipping the other finish, as soon as it has penetrated the outer layer a bit, as an alternative of drilling a perfect Hole.
Regardless of which of the techniques below you go for, 90% of your success will probably be determined not by how the opening will get there, but by the place you place it in the first place. Or, for those who're crazy obsessive (I am), you can make somewhat template with some painters tape. There's not a lot to it: Mark your spot, and place your belt on some scrap wood. Option #3: The Leather Hole Punch This designated device is by far probably the most ultimate option.
Practice on the very finish (that you're going to minimize off later) to get a feel for how the drill and Leather interact. Appears like the Tandy Leather website store has gone kaput, the belt clean and belt preserve hyperlinks don't work any longer. Tom, Unfortunately it appears like this printed around the same time Tandy did a price enhance on the belt clean. Tom: $7 balm + $1 keep + $2 buckle + $19 belt clean = $29 - $10 from code = $19. I already have Sno Seal at dwelling and would like to keep away from buying the Leather Balm if it does the same factor.

Make sure that to place something, that you don't thoughts damaging, that does not move round behind the belt, that is thick sufficient, for when the drill bit goes by. This method takes longer than the others, and leather punch you would possibly find yourself with a messy Hole. You can purchase oval-shaped Leather Hole punches, but most individuals will not notice a mixture of spherical and oval holes.
It should be thinner than the width you used to your belt and long enough to wrap across the width of your belt with slightly further to overlap with. Measure about 1.5″ in. on the tip of the squared tail finish of your belt and mark this spot in the heart of the belt's width after which use your grommet Hole cutter to punch a Hole into the spot you marked. Besides, some of them generally is a little awful on the the actual belt part at occasions.

Leave a Reply

Your email address will not be published. Required fields are marked *